Load

Isotherm Cruise 65 Elegance wiring diagram

Name: Isotherm Cruise 65 Elegance
Brand: Isotherm

See the Isotherm Cruise 65 Elegance connection points and wiring example. Open the diagram in Crimp to add your equipment and plan the cables between them.

Edit this wiring example Add this component to my diagram

Open this example as a new project. Use your own parts and cable lengths to make the plan yours.

Cable sizing for this example

Use the diagram as a starting point for your installation. Replace the example equipment and cable lengths with your own, and check the connections against your exact model's instructions.

3.3 ft one way

12 V system

Wire: 13 AWG · 2.5 mm²
Example fuse: 15 A
Design current: 6 A
Voltage drop: 0.7%

Sized against ABYC E-11. The design current is the part's continuous draw. The length is one way; voltage drop includes an equal-length return.

Run-length and manufacturer assumptions

The editable example uses 3.048 m (10 ft) runs unless a shorter run is stated. Metric overviews round these to 3 m. Adapt the parts and lengths to your installation before choosing cable and protection.

This 12 V example uses the manual's 15 A fuse and 1 m conductors each way. The complete 2 m circuit is within the 2.5 m table entry for 2.5 mm². Recheck the cable table for longer runs. The 24 V version requires different protection; compressor cycling and startup are not a constant daily load. Manufacturer installation manual

Show sizes in mm²

Wiring diagram

How the Cruise 65 Elegance is wired.

Open this example in Crimp to use your own parts and cable lengths. Review the assumptions and installation notes as you adapt the circuit.

Isotherm Cruise 65 Elegance wiring diagram, 13 AWG (2.5 mm²) positive feed protected by a 15 A fuse and a matching negative return between the 12 V battery bank and the unit.6 A · 0.7% drop · ABYC E-11

Edit this wiring example

Installation notes

Connections and installation requirements.

Guidance for this model, with sources linked beside the relevant advice.

Verified against the manufacturer's documentation (rev. CG-FF-19/07/2017 V2.3 — Cruise Classic/Inox/Elegance manual), checked 2026-10-01. Manufacturer documentation →

Which Cruise 65 and what does the energy figure mean?

This entry covers the Cruise 65 Elegance DC refrigerator, identified as CR65EL in the technical table, PDF page 25 / printed page 52. It is rated 6 A at 12 V or 3 A at 24 V, 72 W. Its 275 Wh/day figure is a test at 25°C ambient and +5°C cabinet temperature; it is not a fixed daily consumption in every installation. The catalog's adjustable running hours are a planning assumption.

This scope excludes optional AC power equipment and optional energy-control accessories. Match the full appliance label and fitted controller to the manual before wiring an upgraded unit.

What protection and wiring are specified?

The DC instructions, PDF page 22 / printed 49, require 15 A supply protection at 12 V or 7.5 A at 24 V. Red is positive and black is negative. Use a suitable two-pole isolating switch and avoid a long path through the vehicle control panel that introduces voltage drop. Connect a battery charger to the battery, rather than directly to the refrigerator.

The cable table, PDF page 23 / printed 50, pairs 2.5/4/6/10 mm² conductors with maximum 12 V cable lengths of 2.5/4/6/10 m for the BD1.4F/BD35F/BD50F controller group; the 24 V lengths are 5/8/12/20 m. Confirm the fitted compressor group and the manufacturer's length convention, then check conductor ampacity and total voltage drop for the actual route.

How does the cabinet fit affect performance?

The installation and ventilation guidance, PDF pages 20–21, requires the refrigerator to rest on its support feet and be secured against movement. Keep a path for cool air to enter below the condenser and warm air to escape above or to the sides. Elegance Easy Fix mounting can allow a flush installation, but the door still needs the stated clearance to move freely. Do not use cabinet trim to block the condenser's air path.

How should faults and storage be handled?

Check voltage at the refrigerator during a compressor start, not only at the battery. Loose connections, a restricted condenser or an incorrectly fitted door seal can produce similar poor-cooling symptoms. Use the fault table, PDF pages 26–29, to distinguish supply, fan and compressor faults. For storage, disconnect power, clean and dry the compartment and leave the door ajar; avoid sharp tools when defrosting.

Build it out

Connect it to the rest of your system.

Add Cruise 65 Elegance to your diagram, then connect your batteries, chargers and loads. Crimp calculates cable sizes and checks the connections as you draw.

Every cable you draw there is sized against ABYC E-11, from the same tables as the reference on this page.

Technical reference

Specifications, terminals and supporting parts.

Check the model, ratings and connection points against your own unit before choosing installation hardware.

Catalog specification

Nominal voltage: 12 V
Compatible systems: 12 V / 24 V
Rated power: 72 W
Continuous draw: 6 A

Supporting parts

6.6 ft total of 13 AWG (2.5 mm²) marine cable
Terminations for 13 AWG cable, matched to the equipment's screw terminals, leads or studs
15 A fuse and holder on the positive run
Heat-shrink, strain relief and terminal boots sized to the cable

Check stud sizes, fuse type, run length and how warm the space gets against the gear you actually have before you order.

Terminal map

Catalog connection points, current direction and planning limits. Check the manufacturer's pinout and connector ratings before installation.

TerminalPolarityRoleLimit

pos

positive · input

positiveinput6 A

−

neg

negative · input

negativeinput6 A

Method & provenance

Where the specifications and sizing come from.

Manufacturer specifications describe the equipment. Crimp calculates cable results from the circuit and assumptions you enter.

From the maker

What the catalog says

Manufacturer, model, ratings and which terminal does what come from the catalog. A newer revision, or the nameplate on the unit in your hand, can say something different — when it does, the nameplate wins.

ABYC E-11

What Crimp worked out

Sized against ABYC E-11 — the US reference, and what Transport Canada accepts as an alternative to TP 1332 for pleasure craft under 24 m. The run length and the current above are what drive the result. Crimp doesn't know how warm your space gets; draw the cable inside an engine-bay zone on the canvas and it sizes for the heat.

Read how the sizing works

Next step

Plan your installation with Cruise 65 Elegance.

Open this example as a new project. Add your equipment and cable lengths, then review the sizing and checks for your setup.