12460A-H

Epoch Essentials 460Ah wiring diagram

Essential Series 12460A-H: 12.8 V 460 Ah heated LiFePO4 with Bluetooth and internal BMS. 200 A continuous charge/discharge, with 138 A recommended charging. Deep-cycle battery, not rated for engine starting.

Nominal voltage
12.8 V
Capacity
460 Ah
Maximum discharge
200 A

Wiring diagram

How the Essentials 460Ah is wired.

Open this example in Crimp to use your own parts and cable lengths. Review the assumptions and installation notes as you adapt the circuit.

Epoch Essentials 460Ah wiring example with 4 components: Essentials 460Ah, Battery disconnect, Fused DC distribution, DC fridge. 5 cable connections. Crossings are not junctions.Fused DC distribution 1 to DC fridge +: 11 AWG · 15 A fuse, 10 ft one way. Fused DC distribution 1 to DC fridge −: 11 AWG, 10 ft one way. Essentials 460Ah + to Battery disconnect A: 11 AWG · 15 A fuse, 10 ft one way. Battery disconnect B to Fused DC distribution IN +: 11 AWG · 15 A fuse, 10 ft one way. Essentials 460Ah − to Fused DC distribution IN −: 11 AWG, 10 ft one wayFused DC distribution 1 to DC fridge +: 11 AWG · 15 A fuse, 10 ft one wayFused DC distribution 1 to DC fridge −: 11 AWG, 10 ft one wayEssentials 460Ah + to Battery disconnect A: 11 AWG · 15 A fuse, 10 ft one wayBattery disconnect B to Fused DC distribution IN +: 11 AWG · 15 A fuse, 10 ft one wayEssentials 460Ah − to Fused DC distribution IN −: 11 AWG, 10 ft one wayEpoch Essentials 460AhEssentials 460Ah++−−Main Battery SwitchBattery disconnectABBlue Sea 5025 ST Blade Fuse BlockFused DC distributionIN +IN +IN −IN −1111Dometic CRX-65 Fridge. This 12 V example uses Dometic's 15 A supply protection and a short 1 m run with 6 mm² cable. Check the manual's voltage-specific cable graph for your route. At 24 V, the specified protection is 7.5 A. Running current and the fuse rating describe different things.DC fridge++−−11 AWG · 15 A fuse11 AWG11 AWG · 15 A fuse11 AWG · 15 A fuse
Epoch Essentials 460Ah wiring example with 4 components: Essentials 460Ah, Battery disconnect, Fused DC distribution, DC fridge. 5 cable connections. Crossings are not junctions.Red = positive · dark = return · dashed = signal. Cable labels are example values; use the equipment instructions and actual installation lengths.
Edit this wiring example

Cable sizing for this example

Use the diagram as a starting point for your installation. Replace the example equipment and cable lengths with your own, and check the connections against your exact model's instructions.

Cable sizes depend on the connected equipment, current and cable lengths. Add those details in Crimp to size each run.

View diagram in mm²

Installation notes

Before you install.

Open a question for model-specific guidance and sources.

Verified against the manufacturer's documentation (rev. 12460A-H V02, September 2026), checked 2026-10-20. Manufacturer documentation →

Match the Essentials model

This entry is the 12460A-H Essential Series: a 12.8 V, 460 Ah LiFePO4 house battery with 5,888 Wh nominal energy, internal BMS, heating and Bluetooth. Verify the model and ratings on the installed unit. The manufacturer product page and V02 documents identify this model separately from the B12460, which has different current limits. This battery is not cranking rated.

Keep continuous and peak ratings separate

The V02 specification gives 200 A continuous charge and discharge, with 138 A recommended charging and discharge. Crimp uses the 200 A continuous limits. The 400 A peak for up to ten seconds is temporary and does not increase the continuous budget.

Set the charger for this battery

The manual's charging section, pages 20–22 specifies 14.2–14.4 V bulk/absorption and 14.6 V maximum. Disable float if possible, or use 13.3–13.6 V. Use the model's heating and temperature instructions before charging in cold conditions; the presence of a heater does not permit charging cold cells without its protection.

Connect and protect the bank

The V02 technical datasheet, pages 3–4 identifies M8 female terminals, 8–12 Nm terminal torque, and a maximum 4S4P arrangement. Follow the supplied hardware and installed revision's instructions. Use matching batteries and follow the manual's commissioning sequence before connecting a bank.

Install a suitably rated main fuse or DC breaker close to battery positive. The internal BMS and its 200 A rating do not select an external fuse; protection must suit the actual cable, equipment, bank and available fault current. See connection guidance, pages 13–17.

Technical reference

Specifications and terminal map.

Check the model, ratings and connection points against your own unit before choosing installation hardware.

Catalog specification

Essential Series 12460A-H: 12.8 V 460 Ah heated LiFePO4 with Bluetooth and internal BMS. 200 A continuous charge/discharge, with 138 A recommended charging. Deep-cycle battery, not rated for engine starting.

Nominal voltage
12.8 V
Capacity
460 Ah
Maximum discharge
200 A

Terminal map

Catalog connection points, current direction and planning limits. Check the manufacturer's pinout and connector ratings before installation.

+

positive · bidi

200 A

−

negative · bidi

200 A
Sources and sizing method

Equipment specifications. Model details, ratings and terminal roles come from the catalog. Check your unit’s label and current manufacturer documentation for its exact revision.

Example sizing. Cable labels apply to the connected example, not a fixed cable size for this component. Set your actual equipment, current, lengths and installation conditions in Crimp before choosing hardware.

Read how the sizing works

Next step

Plan your installation with Essentials 460Ah.

Open this example as a new project, or add this component to your existing diagram. Use your equipment and cable lengths to review the sizing.

Start drawing, sizing and checking without an account. Your drawing saves in this browser. See Pricing for the equipment allowance and the one-time export offer available to you.