Load
See the Golight Stryker ST 30004ST LED Searchlight connection points and wiring example. Open the diagram in Crimp to add your equipment and plan the cables between them.
Open this example as a new project. Use your own parts and cable lengths to make the plan yours.
Use the diagram as a starting point for your installation. Replace the example equipment and cable lengths with your own, and check the connections against your exact model's instructions.
10 ft one way
12 V system
Sized against ABYC E-11. The design current is the part's continuous draw. The length is one way; voltage drop includes an equal-length return.
The editable example uses 3.048 m (10 ft) runs unless a shorter run is stated. Metric overviews round these to 3 m. Adapt the parts and lengths to your installation before choosing cable and protection.
This supply example retains the manufacturer's 5 A fuse. Follow the complete installation notes for connector polarity, mounting, controls and commissioning; verify the actual cable route and equipment revision. Manufacturer installation manual
Wiring diagram
Open this example in Crimp to use your own parts and cable lengths. Review the assumptions and installation notes as you adapt the circuit.
This supply example retains the manufacturer's 5 A fuse. Follow the complete installation notes for connector polarity, mounting, controls and commissioning; verify the actual cable route and equipment revision. Manufacturer installation manual
Edit this wiring exampleInstallation notes
Guidance for this model, with sources linked beside the relevant advice.
Verified against the manufacturer's documentation (rev. ST Series Wireless Instruction Guide, undated), checked 2026-10-01. Manufacturer documentation →
30004ST is the white permanent-mount LED Stryker ST. Its instruction guide lists 3.5 A maximum at 13.8 V and a 5 A fuse. Other models in the same guide are halogen with different current and fuse requirements. The light needs a 12 V vessel supply; it is not a direct 24 V appliance. The handheld remote runs from its own two AAA cells and does not take its operating power through the light’s supply cable.
Connect the identified positive and negative light leads to a protected supply and return, retaining a 5 A fuse for the LED model. Identify the actual harness before relying on wire color. Size extensions for the route and loaded voltage drop; the guide does not publish a universal extension-gauge limit. Leave about 3 inches of cord beneath the mounting surface as instructed, support the route and keep wiring clear of the moving head.
The head rotates 370 degrees overall, about 185 degrees each way, and tilts through 135 degrees. Allow its approximately 11.3-inch swing diameter and avoid obstructions. Follow the mounting footprint and seal the cable hole. Do not seal the base gasket’s drainage path. The instructions prohibit inverted mounting and underwater use; an inverted installation is not made acceptable by extra sealant.
Use the matching ST remote. Select spotlight 1 on the remote as instructed. Hold the remote’s power and speed buttons together while restoring light power; the guide allows learning in the first six seconds after power-up, and three flashes after three seconds confirm pairing. Test left/right and up/down travel in short movements, then full clearance without directing the beam at people. Check steady operation while moving the head. If aiming is intermittent, inspect remote batteries, pairing and supply voltage before changing the fuse or forcing the mechanism.
Golight installation manual, ST Series Wireless Instruction Guide, undated; two-page manufacturer instruction sheet: mounting, pairing and separate LED/halogen electrical tables; retained from Flak mirror. The original PDF is retained in the marine source ledger. The drawing represents the identified electrical interfaces; it does not simulate the equipment’s mechanical performance, radio signals or fluid system. Unpublished connector ampacity and startup current remain unspecified.
Build it out
Add 30004ST to your diagram, then connect your batteries, chargers and loads. Crimp calculates cable sizes and checks the connections as you draw.
Every cable you draw there is sized against ABYC E-11, from the same tables as the reference on this page.
Technical reference
Check the model, ratings and connection points against your own unit before choosing installation hardware.
Check stud sizes, fuse type, run length and how warm the space gets against the gear you actually have before you order.
Catalog connection points, current direction and planning limits. Check the manufacturer's pinout and connector ratings before installation.
Supply +
pos
positive · input
Return −
neg
negative · input
A dash means a current rating is not specified here.
Method & provenance
Manufacturer specifications describe the equipment. Crimp calculates cable results from the circuit and assumptions you enter.
From the maker
Manufacturer, model, ratings and which terminal does what come from the catalog. A newer revision, or the nameplate on the unit in your hand, can say something different — when it does, the nameplate wins.
ABYC E-11
Sized against ABYC E-11 — the US reference, and what Transport Canada accepts as an alternative to TP 1332 for pleasure craft under 24 m. The run length and the current above are what drive the result. Crimp doesn't know how warm your space gets; draw the cable inside an engine-bay zone on the canvas and it sizes for the heat.
Next step
Open this example as a new project. Add your equipment and cable lengths, then review the sizing and checks for your setup.